WB Electronics
Back
Support - Infinity USB
Installation instructions
· Windows 98
· Windows ME
· Windows 2000
· Windows XP/Vista/7

User's guide (web)
· Quickstart
· Detailed

Frequently Asked Questions
· F.A.Q

How to
· Identify serialnumbers
· Use the commandline interface

User forum
· Forum


Frequently Asked Questions - F.A.Q
1. I have a problem installing Infinity USB or Infinity USB Phoenix on Windows XP (error code 10).
2. When inserting a card, the following message is displayed: "No CPU could be detected on the inserted card..."
3. When programming a card, the following error occurs: "Could not verify location"
4. Can Infinity USB be upgraded to support Phoenix mode?
5. Is software available for Linux or MacOS?
6. I think I may have bought an Infinity USB clone, what should I do about it? / I have an M5 or blue Digitech programmer, where can I find the latest software-update for it?
7. My Infinity USB (Phoenix) came with a CD, and I have installed all the software on the CD, but the Smartmouse and Funprogrammer software doesn't work?

1. [Q] I have a problem installing Infinity USB or Infinity USB Phoenix on Windows XP (error code 10).

[A] This error arises due to a faulty driver installation. This is mostly caused by to a broken cable, trying to install the wrong driver or in rare cased a compatibility issue with specific motherboards/USB controllers, Infinity USB (Phoenix) and Windows XP (see below).

The Infinity USB hardware will continue flashing, and not be accessible by the software (programmer disconnected). The driver is not installed correct before the blue LED lights up constantly (without any smartcard inserted).

To solve the problem, first try connecting the programmer to a new USB port with another USB cable. Then reinstall the drivers downloaded from the download-page (complete diskimage). Make sure you have the right privileges (logged in as Administrator) to install a driver.
 
2. [Q] When inserting a card, the following message is displayed: "No CPU could be detected on the inserted card..."

[A] The most likely cause for this, is either dirty contacts on the card, or the card facing in the wrong direction. The card can be cleaned with isopropyl alcohol, and must be inserted with the contacts facing down.

Another reason may be that you're inserting a card that Infinity USB (Phoenix) doesn't support natively. Cards like Basiccard and titaniumcards needs to be accessed in phoenix-mode, with the appropriate 3rd party software.
 
3. [Q] When programming a card, the following error occurs: "Could not verify location"

[A] You may have a faulty card, or a card with dirty contacts. If you didn't do a full detect before programming you may have selected the wrong card.
 
4. [Q] Can Infinity USB be upgraded to support Phoenix mode?

[A] An Infinity USB Phoenix contains almost twice as much hardware as an Infinity USB. It's therefore not possible to upgrade an Infinity USB to support phoenix mode.
Even though the latest Infinity USB uses the same printed circuit board as the Infinity USB Phoenix and therefore theoretically could be upgraded, the components needed and time/effort upgrading the unit exceeds the cost of a new Infinity USB Phoenix.
 
5. [Q] Is software available for Linux or MacOS?

[A] It is possible to use Infinity USB under MacOS using VirtualPC, and for Linux users, nftytool for both Infinity USB and Infinity USB Phoenix can be used.
 
6. [Q] I think I may have bought an Infinity USB clone, what should I do about it? / I have an M5 or blue Digitech programmer, where can I find the latest software-update for it?

[A] The Digitech and M5 programmers are illegal copies of the Infinity USB and WB Electronics will ofcourse not support the clones. Other clones are also available (which has nearly the same casing as an Infinity USB, typically with a red, green or yellow LED instead of blue, only 1 LED in the plastic casing, and with no serialnumber), and they will ofcourse also not be supported.
The current software-releases are not working with the Digitech or M5 clones, and we are working actively to make sure forthcoming versions wont work with the clones either.

If you suspect your Infinity USB to be a clone, contact us and we can easily determine if you have an original product, or a clone.

WB Electronics are the original developers and manufacturers of the Infinity product range, and the clones makes it impossible for us to invest the time and money needed for developing new products, and to provide new software releases for current products. We therefore recommend anyone who have bought a clone to return the programmer for a refund.
 
7. [Q] My Infinity USB (Phoenix) came with a CD, and I have installed all the software on the CD, but the Smartmouse and Funprogrammer software doesn't work?

[A] The CD included with Infinity USB, Infinity USB Phoenix, Funprogrammer USB and Smartmouse USB contains software for all 4 products. You only need to install the Infinity USB (Phoenix) software for the Infinity USB or Infinity USB Phoenix hardware. The software contains all features of the other 2 products, and the software for Funprogrammer USB and Smartmouse USB can't be used with Infinity USB or Infinity USB Phoenix.
 
Copyright ©2001-2024 WB Electronics - All rights reserved - Privacy policy