WB Electronics
Back
Support - Smartmouse USB
Frequently Asked Questions
 F.A.Q

User's guide (web)
 Infinity PasswordSafe
 Infinity PasswordSafe WinLogon
 Infinity SIM Editor

How to
 Optimize performance
 Identify serialnumbers
 Use the Phoenix/Smartmouse interface

User forum
 Forum


How to - Use the Phoenix/Smartmouse interface
This guide will give an understanding of the basics of Phoenix/Smartmouse (PH/SM) and how to set up the PH/SM compatible programmers for use with various 3rd party software.

The PH/SM interface is needed to program the cards not supported natively by the Infinity USB software, such as Titanium, M2, GSM/SIM-cards etc.


The Phoenix and Smartmouse standard is defined by a very simple serial (COM-port) based interface for communicating with a smartcard using the ISO7816 standard.
The PH/SM interface supplies power to the card, a clocksignal running at typically 3.58MHz, and it communicates over a single bi-directional connection at 9600bits per seconds (equivalent to approximately 372 clockcycles pr. bit).

The big difference between a smartcard programmer like the Infinity USB, and a PH/SM interface, is that the programmer programs software/data onto the CPU and memory on the smartcard, while a PH/SM interface communicates with the CPU on the card.
It may be possible to write certain parts of a smartcard with a PH/SM interface, but it entirely depends on the software (pre)programmed on the card, and the PC-software. In some cases a PH/SM interface is required to program data to a specific smartcard, either because encrypted communication is wanted, or because only dedicated 3rd party software can be used for accessing the smartcard.

For further information on smartcards and communication, see the ISO7816 standard.


Setting up the interface is straightforward, but since a number of different factors are involved when using 3rd party programs, there may be potential pitfalls. It is therefore adviseable to use the guide below, and do a full setup-test with the PH/SM testsoftware supplied by WB Electronics, before using any 3rd party software.

  1. Connect the Smartmouse USB to the PC, with the USB cable.


  2. If the interface is connected for the first time, the driver has to be installed (available on the drivers-CD that came with the product).


  3. With no cards in the cardreader, start the Smartmouse USB software.


  4. Press [Auto detect], and the software will automatically find the COM port the Virtual COMport has been assigned. To change the COMport (for instance if your 3rd party software doesn't support more than COM1-4, see the Smartmouse USB F.A.Q).
    Choose frequency and polarity and press [Enable]
  5. The software will minimize to systray.

  6. Insert the card to be accessed by the 3rd party software. The orange LED will flash while data is being transmitted from or to the smartcard.
Testing the entire setup is easy with the use of the PH/SM testsoftware supplied by WB Electronics, which can be downloaded from the downloadpage.
  1. Remove any cards from the Smartmouse USB.

  2. Make sure no other 3rd party software has locked the COMport, and open the PH/SM testsoftware.

  3. Press [Auto detect] and if everything is setup correct, a message will popup telling which COMport the device is attached to. "Status" will change from "Disconnected" to "Connected".

  4. Insert the card you want to access using a 3rd party program. "Status" will change from "Card NOT inserted!" to "Card inserted!"

  5. Press [Test]. The window will either report "Test failed on COMx" (in the case that the testprogram didn't get an ATR (Answer To Reset, a kind of identification string) from the card). This could mean that either the card has no valid loader, or the wrong frequency was chosen when setting up the Smartmouse USB.
    If the card returns a valid ATR (meaning that it may be possible to write it with the appropriate 3rd party program), the PH/SM testsoftware display the ATR:


     Reset mode: Smartmouse
     ATR length: 12
     ATR HEX   : 3B19943303013145410602B6
     ATR ASCII : ;.3..1EA..

    (example from a GSM/SIM card)


  6. Close the PH/SM testsoftware by pressing [Exit]. The interface has now been succesfully tested, and the settings for various 3rd party software has been found (COMport number, frequency, valid smartcard).

The use of 3rd party software is supported by WB Electornics thru Phoenix and Smartmouse but WB Electronics do not offer help/support on issues regarding software not developed by WB Electronics.
Copyright 2001-2017 WB Electronics - All rights reserved - Privacy policy